Certified for use on power vessels under 20 meters (65.6\') in length....

Certified for use on power driven vessels under 20 meters (65.6\') in length....

Not approved for use below the water line....

For use with systems from 6-32 volts. Capacity - rated 450 amps continuous, 1200 amps intermittent (15 seconds on, 5 minutes off). Ignition protected. Alternator Field Disconnect (AFD) enabled....

...

...

Pro IsoCharge delivers digitally controlled alternator output distribution while protecting the health of engine start batteries. Eliminate typical alternator voltage loss of up to .6VDC that is commonly associated with traditional diode based isolators. Intelligent zero volt loss isolation ensures fully charged batteries and faster charging times....

PronauticsP optional remote available for interactive remote port for digital display and control....

As with any rubber hose below waterline, the PSS bellows must be inspected on a regular basis for any sign of wear, aging or chemical deterioration. The PSS bellow, O-rings & set screws should be replaced in six year intervals. Bellows may need to be more frequently inspected in an environment where non-sealed batteries emit sulfuric acid. Sulf...

T-Kits help facilitate the installation of the PSS Shaft Seal. These T-Kits enable the installer to tee into the raw water discharge hose and plumb water to the hose barb fitting of the PSS Shaft Seal. Some examples of water pick-up points are:A. Between the heat exchanger and riser.B. Between oil cooler and heat exchangerC. Between the water pump ...

Over time you may find that you need to replace the O-rings inside the stainless steel rotor of your PSS Shaft Seal. This kit comes with everything you need to get the job done. Includes: Allen wrench, (5) Set screws, (2) O-rings, (4) Clamp Jackets, Thread lock....

Designed to help retain the propeller or rudder shaft in your vessel in the event of catastrophic failure of the coupling or if the shaft comes free from the coupling. The double split design provides the maximum in axial holding power. Quick assembly with the shaft installed. Fully engages the shaft without marring. A cost effective and quick solu...

The 200 series fuel filter/water separators feature a Spin-On, high capacity Aquabloc® II replaceable filter element which separates water, and removes solid contamination. All models are standard with 1/4\"-18 NPTF inlet and outlet fuel ports. An integral priming pump and a new see-thru contaminant bowl can operate in applications up to 30 PSI. T...

All 400 Series spin-on fuel filter/water separators feature a hand (palm) operated fuel priming pump which simplifies service procedures. These filters also feature multiple fuel ports (two inlets and two outlets) and a unitized mounting bracket for installation convenience. Additional 400 Series features include spin-on, high-capacity, Aquabloc®I...

Bent ferrule disposable brush, use for hard to reach areas. Bristle is pure black and polyester material. Square trim and sanded wood handle....

Paint roller cover, caged frame and metal tray set. Individually poly wrapped....

For use with 3/8\" or larger drills....

Ideal for dockside, utility or sump pump use. 110 Volt AC pump features heavy duty construction for a wide range of uses and applications. 90° Elbow adapter for connecting discharge nozzle to standard pipe thread and an 8\' power cord....

...

High strength, low stretch, and very low weight make WarpSpeed® II the high-performance racers choice for double braid ropes. The strength member is 100% SK78 fiber. The cover is a flexible 24-strand ployester that provides good handling, excellent performance in stoppers and clutches, and enhanced abrasion resistance. The cover can be stripped wh...

Accessory Cord has excellent flexibility, knotting, and strength characteristics for a free running, torque-free cord....

Control-DPX™ combines Dyneema® fiber and Samson\'s patented DPX™ fiber technology into a strong, lightweight line that is winch and cleat friendly, while being incredibly easy on the hands. DPX™ adds the grip and \"soft-hand\" feel of spun polyester to the lightweight strength of Dyneema® fiber. The result is an easily spliced, 12-strand si...

Bright Yellow with a Red identification tracer line. 100% Olefin fibres. Highly visible, floats, excellent handling qualities, non-torquing....

Fid pushers are used in rope splicing to push the tubular fids attached to the rope through the rope to complete the bury, and also can be used to help extract core fibers when beginning the splice. Choose the size of fid pusher corresponding to the rope diameter you want to splice....

SmartStick is a non-contact autopilot position sensor that mounts to outboard front mount cylinders. For Raymarine autopilots....

Can be used with all BayStar helms with appropriate fittings. Kit contains two cut lengths of tubing.(NOTE: BayStar Cylinders with H suffix must use tubing part number with H suffix.)...

3dB antenna. Brass and copper elements for performance, plus a smooth, high-gloss, polyurethane finish that wont turn yellow in the sun. Chrome-plated brass ferrule with standard 1\"-14 thread. Includes 15\' RG-58 cable and a PL-259 connector....

The Classic 5120 AM/FM antenna utilizes high-end features. When youre far from your favorite stations, this antenna helps bring them in loud and clear....

End-fed 1/2-wave stainless steel whip. This compact, lightweight antenna is ideal for vessels where space is limited. Its chrome plated brass canister minimizes de-tuning. 15\' cable and PL-259 connector included. Requires mount with center hole for cable passage....

Designed especially for small boat applications needing only short range communications, the 5912 is a small, space-saving antenna that attaches and detaches with ease, once the included Flush Mounting Kit has been installed. The connectors are gold plated for low-loss performance. Its compact, light weight, and easily stored....

Designed to meet the broader bandwidth requirements of all popular AIS transceivers. Commercial-grade construction with a mast mounting sleeve. White fiberglass finish....

Stainless steel. Mount comes with nylon adaptors to fit 7/8\", 1\" and 1-1/4\" rails. Standard 1\"-14 thread. Can also be mounted to flat surfaces....

AIS marine band 3dB gain. Communication performance over marine frequencies is optimized with the master craftsmanship of this Classic 5215 Squatty Body®, built with extra bandwidth for all popular AIS transceivers. The lightweight, low-profile, stainless steel VHF antenna is designed for masthead mounting to enhance transmission quality....

AIS Marine band w/6dB gain. Cruise with confidence and communicate reliably over the AIS band. Specifically designed to meet the broader bandwidth requirements of all popular AIS transceivers, it features commercial-grade fiberglass construction to ensure performance and durability and a stainless steel ferrule with 1\" - 14 thread. Includes 20\' R...

Used to increase the height of an antenna and improve effective range, or to boost placement of an antenna above on-board obstructions. Constructed with high-quality pristine white fiberglass and hand finished to match Galaxy® antennas. Stainless steel upper and lower ferrules with standard 1\"-14 thread....

Designed to meet the broader bandwidth requirements of all popular AIS transceivers, this antenna mounts with ease. Its compact size will be welcome aboard any vessel. Chrome plated brass canister minimizes the de-tuning associated with antennas having plastic canisters....

Gets your point across with up to 40 watts power handling capacity and also supports loudhailer listenback function. It is made of high impact white plastic and includes a tilt mount bracket....

Absorbs shock and reduces vibration. Durable EDPM synthetic rubber compound offers superior resistance to water absorption, sunlight damage and extreme temperatures. With adhesive backing, its ideal for livewells, exterior doors, instrument covers and electronic boxes....

Extra tackle storage is always a necessity on a boat. Features 4 individual removable boxes w/lids. The boxes lock into position to prevent sliding out while under way or in rough weather with the door open. Uses the same hatch as our 1115 Access Cam, and can also be retrofitted with a locking mechanism....

Not just durable, but comfortable and functional as well, the All-Weather™ features a double contoured seat pan that eliminates pressure points. Stainless Steel hinge pins and included proprietary Quick Disconnect Mount provides for even more functionality. The QD mount allows the seat to swivel on a low profile corrosion proof disk, and can be r...