Injection molded UV stabilized nylon construction with dual swiveling mounts for full adjustability. Designed to feed the antenna wire directly through the base eliminating the need for a separate cable outlet, reducing potential areas for water leakage. The control knob allows for quick and easy adjustment diminishing the potential of mooring, fis...

Molded to the highest standards using top quality UV stabilizers and antioxidants. When installing, use silicone sealant on hull or deck surface. Lubricate with Vaseline or Teflon grease. Installs with six #8 FH fasteners (not included). Avoid contact with acetone or strong solvents....

Constructed of impact resistant injection molded ABS and designed to be used in conjunction with a collector box. Installs with four #8 FH fasteners (not included). Avoid contact with acetone or strong solvents....

Stamped 304 stainless/lexan blades.Slip-on hinge style wiper blades and arms fit all current Sea-Dog® wipers. Verify style prior to ordering. Wiper arms fit all standard and waterproof standard motors with 3/8\" shaft diameter. Note, blades do not fit 413 series arms.Hook style wiper blades and arms are replacements for Sea-Dog® wipers sold prior...

Illuminating Toggle Switches are constructed of stamped brass and injection molded nylon with a polycarbonate toggle. Features a locking ring and lever seal to resist water penetration. Illuminates red in the ON position. Fits panels up to 1/4\" thick and requires a 15/32\" mounting hole. 1/4\" spade terminals make it easy to install. 15A @ 12VDC....

Splash Guard On-Off Push-Pull Switch is constructed of stamped brass with PVC coating to protect terminals and switch from water (not designed for immersion). Features positive actuation with two positions On-Off (normally Off). Maximum panel thickness: 7/8. 15A @ 12VDC....

Mounts in a 5/8\" hole. Stamped brass construction and a PVC coating protects the 2 screw terminals and switch from water. Not designed for immersion. Max panel thickness: 3/4. 15A @ 12VDC....

ACG Watertight Inline Dual Fuse Holder is constructed of injection molded PVC. Feature snap tight connection for use in wet or semi-wet locations. Includes standard 1/4\" x 1-1/4\" glass fuse and an extra emergency fuse. Fuse holder has a specially designed case that is molded with a second fuse pocket for convenient access to a spare fuse....

Constructed of stamped anodized aluminum. Features six 15A 12VDC illuminated SPST On/Off rocker switches and six thermal AC/DC circuit breakers (two 3A, two 6A, one 8A, and one 10A). Individual circuit 10A max. 40A total. 12VDC. Includes a sheet of 20 preprinted decals to customize to your specific applications. Installs with six #6 RH fasteners (n...

Constructed with an injection molded thermo plastic body and cap, with machined brass polarized pins. For use as a 4-conductor deck cable outlet. Pins are sized differently, ensuring only one way to connect the plug and avoiding reverse polarity issues. 5A. 12 or 24VDC. Installs with two #6 FH fasteners (not included)....

Terminal Blocks are modular, insulated, screw-type electrical connectors that are used to secure and/or terminate two or more wires together. Useful for connecting wiring to a ground or for connecting electrical switches and outlets to the mains. Molded Bakelite and stamped brass construction. Designed for use with tinned copper marine wire which s...

Electrical Buss Bars provide a convenient way to connect electrical wires, prevent shorts, eliminate splicing, tidy up wire harnesses, and conserve panel space. Non-fused, these distribution blocks are used primarily for routing and connecting power or ground circuits. Molded Bakelite and stamped brass construction. Designed for use with tinned cop...

Manufactured from high-density polyethylene with UV-stabilized resin. Mechanically vented fuel cap ensures easy gripping. Features rotating 90°, 1/4\" NPT fuel withdrawal elbow that eliminates kinked fuel lines. Includes mechanical direct-sight gauge with easy-to-read indicator. Specifically designed for use in Boston Whalers, Carolina Skiff and K...

Swingarm Electric Sending Units gather fuel level information the same way as the mechanical sending units. It does, however, connect to a dash mounted gauge without a conversion capsule. Internal components will not rust or corrode. Float rotates easily in 90° increments for tanks wall & baffle clearance....

...

With a direct sight gauge or with the conversion capsule gathers fuel level information with the float. While accurate, the gauge will fluctuate as the fuel in the tank \"sloshes\" around the tank when boating because of the moving parts - the float. Direct site gauge is included with the sender....

...

Converts fuel level reading from standard direct site gauge to electric dash mounted gauge (33-240 Ohms\'s)....

...

...

Marine rubber antenna....

...

...

Acetal construction.Threaded female end fits A-series aerator pump outlets and Tsunami threaded outlets. Barbed end....

Fully adjustable mirror. Movable feet, securing clamps and tightening knob for a secure fit without annoying vibration! Aerodynamic and durable styling....

Utilizing our reversible flexible impeller pump technology, ballast systems can be filled or emptied. Available with or without Reversing Polarity Switch to fill or empty ballast tanks. Includes run-dry impeller. Complies with USCG 183.410 and ISO 8846 MARINE (Ignition Protected). 1\" (25mm) hose barb or \" NPT internal port.Model 18220-1127 includ...

Makes boat seat installation easy....

Positive locking disconnect allows quick installation or removal of any standard swivel seat. Fits 6\" swivel WD10. Durable molded plastic, steel rail frame, stainless steel spring....

...

7410500: Plastic mesh , fastening clamp included77125: Two-piece filter, easily installs by placing the mounting base under the aerator thru hull nut and then tightening the nut. Twist off to remove for easy cleaning....

...

Rolled acme threads and anti-friction thrust bearings provide smooth cranking and long cycle life. High strength tubing and ample tube overlap delivers safe, strong service for years. Features 1:1 sidewind gear ration providing more travel (14\" total) with less cranking to lift or lower the jack....

Waterproof. Snap lock base mount. Includes lamp, black base, and black wire. A frame ground eliminates the second wire....

Designed for trolling motor steering connectors. The ball stud is 3/8-24 thread by 1-7/8\" long. Body is tapped for 3/8\"-24 threaded rod. Made from zinc plated steel....

...

3 Recessed to holes for flush fit to boat\'s transom or exterior, allowing water to drain when boat is trailered. Plug has screwdriver slot and rubber O-ring to seal water tight....

Transom Drain Tube Plug only for 020303-001....

Designed for aluminum boats as a 1\" drain for transom, livewell or baitwell. Easily flanged, fitting eliminates need for welding. An O-ring forms a watertight seal in .40\" to .090\" wall thickness....

For mounting from inside transom. Fully adjustable, creates waterproof seal and will not leak or jar loose under vibration. Corrosion resistant construction. Designed for use with Moeller drain tubes. All come with neoprene seal....

Special alloy. Flanged 90° one end. Functions as drain for transom, motor well, livewell or baitwell. Use similar metal between tubes and plugs. Designed for use with Moeller Snap-Tite, Turn-Tite and Trail \'n Bail Plugs. Wall thickness is .035\". Length under flange given....